.
Category: Analysis devices
.
.
3X1 NBR gasket for Divesoft analyser hose
Spare kit of O-rings for DIVESOFT He/O2 Analyzer and jumper for firmware upgrade
Bleed valve consists of bleed valve body, bleed valve screw, o-ring 4x2 NBR70 and stainless steel ball 1/8".
Connection hose for use with professional, standard or inflator flow limiters.
It is meant for the cylinder low-pressure connection with the diameter of 5.8 mm..
Professional flow limiter MK2 G5/8
The Professional flow limiter Mk2 is equipped with a regulator that reduces the gas to flow at a constant rate regardless of the cylinder pressure. This enables the gas sampling to remain accurate even at very low pressures. This feature has proven to be critical during gas blending procedures.
The standard limiter works on the principle of a throttle nozzle. Its flow is therefore dependent on the tank pressure. T
he greater the pressure, the greater the flow is. Therefore, it is suitable for divers to check the mixture before the actual dive.
The flow limiter with connection to the DIN - G 5/8" for 200 and 300 bars, with needle valve. The connection hose is not included.
Gas flow depends on the inlet pressure.
Doivesoft He/O2 analyzer is a precise apparatus for measuring oxygen helium concentrations in diving breathing gasses. It is a necessary tool for technical divers using nitrox and trimix mixtures.
Professional Set Blender Basic was compiled for divers and mainly for filling stations, which prepare Nitrox and Trimix and which want to have analyzer stored in the watertight case .
Set Blender Basic contains professional flow limiter.
Professional Set Blender Max was compiled for divers and filling stations, which prepare Nitrox and Trimix gas mixtures.
The analyzer can measure resistance and voltage and can be stored in the supplied waterproof Peli Case 1200.
Set Blender Max contains professional flow limiter.
Analyzer SOLO is a precise apparatus for measuring oxygen and helium concentrations in scuba diving breathing gasses. It is a necessary tool for technical divers using nitrox and trimix mixtures.
A smart and accurate NITROX analyzer that offers simple oxygen measurement and advanced features.
Analyzer SOLO O2 is the ideal partner for all recreational NITROX divers.
Analyzing is really easy, just turn on with one press and measure. Easy automatic calibration. Analyzer SOLO O2 has the same durable polymer body as its brother Analyzer SOLO, allowing you to upgrade to a trimix analyzer by adding a helium sensor*.
Freedom computer can be used as a nitrox analyzer if an oxygen sensor is attached.
Just order Freedom Nitrox analyzer.
The analyzer is supplied WITHOUT an oxygen sensor.
Use Divesoft R22S oxygen sensor with Molex 3-pin connector or equivalent like our NRC oxygen sensor D05-R
Oxygen sensor previously used in rebreather (type R22-D) can also be used in the probe, if they are still able to measure full range of oxygen pressures in atmospheric pressure safely.
Ohm-meter plug-in.
For example: bulbs check, cables check.
After connection to the He/O2 analyzer the measuring of impedance in range of 0 — 1000 ohms is automaticaly switched on.
There is an option to have an acustic signal when the impedance goes under 200 ohms.
With this product we recommend to order measuring cabels #1058.
Voltmeter plug-in for example: battery check (lights, scooters...).
After connecting to the He/O2 Analyzer it automatically switches itself into measuring mode.
It measures the varying tension up to 28 V (RMS) and the constant tension up to 40 V with polarity indication.
We recommend you to order measuring cord #1058..
Simple connector to the DIN G5/8 valve. The connection is placed into the gas input port of the analyzer and pushed against the tank valve.
Gas flow is regulated using the tank valve. It is suitable for a fast analysis of gas in several tanks. With some valves is may be difficult or even impossible to set a low enough gas flow – in such case use a flow limiter or regulator.
The connection to an inflator hose enables the measuring of mixtures in already dressed tanks without the need of removing the second stage regulators.
You only need to disconect an inflator or other quick release connector, which will output a flow of 0.2 l/min at 10 bar.
The connector is cylindrical with a diameter of 5.8 mm, to the He/O2 analyzer it is connected via a connection hose.
Simple connector to the DIN G5/8 valve. The connection is placed into the gas input port of the analyzer and pushed against the tank valve.
Gas flow is regulated using the tank valve. It is suitable for a fast analysis of gas in several tanks.
With some valves is may be difficult or even impossible to set a low enough gas flow – in such case use a flow limiter or regulator.
Simple flowmeter for checking of the flowing air from a professional or standard limiter. It can also be used for calibration of a standard flow limiter.